Every metal roof installation in Connecticut we sell includes the full tear-off, new underlayment, and finished trim, not a stripped-down line item list. Here's what's in the base scope, and where add-ons like snow guards or skylight flashing come in.
We strip every layer of old roofing down to bare decking, not a layover. That lets us inspect the sheathing for rot and replace what's soft. All old shingles, felt and nails leave in our dumpster, and the lawn gets magnetically swept before we pull out.
Self-adhering membrane goes along the eaves, in valleys and around every penetration. In a climate that freezes and thaws 60-plus times a winter, this is the layer that stops ice dams from backing water under your panels. We don't skip it to shave the bid.
Your chosen panel profile, cut to length on site, plus color-matched ridge caps, drip edge, gable trim and closure strips. Concealed clips or fasteners are included, along with pipe boots and new step flashing at sidewalls. Nothing is billed as a surprise extra.
We balance intake at the soffits with ridge vents at the peak so the attic breathes. That prevents attic condensation, which is the quiet killer of roof decking in Connecticut homes. If your existing venting is undersized, we'll correct it during the install.
Manufacturer finish and structural warranties get registered in your name before we leave, and you receive the paperwork plus our own workmanship coverage. If a fastener backs out or a panel shifts in the first year, one call brings us back at no charge.
Metal Roofing in Connecticut is a concealed-fastener or exposed-fastener panel system that sheds water, snow and ice instead of absorbing them. We tear off the old asphalt shingles down to the roof decking, replace any rotted sheathing, then lay ice and water shield along the eaves and valleys before the panels go down. Panels are cut on site, fastened through pre-punched ribs or clips, and finished with color-matched ridge caps, drip edge and pipe boots. Standing seam panels float on clips so the metal expands and contracts with Connecticut's 100-degree temperature swings without backing out a single screw.
Most Connecticut roofs we replace are 20 to 30-year asphalt shingle systems that have already lost their granules to hail damage and wind damage. Homeowners call us after a February ice dam pushes water through the ceiling, or after a nor'easter peels shingles off a ridge in Danbury or Torrington. A metal roof installation Connecticut homeowners choose once and stop thinking about is the answer to both problems: snow slides off a smooth panel, and there are no shingle tabs for wind to grab. If you're pricing metal roofing cost in Connecticut, the honest range for a full tear-off and install is $14,000 to $38,000 depending on square footage and panel type.
Five steps from first call to final walkthrough. No mystery, no surprise line items, and one crew on your roof from tear-off to cleanup.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Tools & EquipmentStanding Seam Clip System
Concealed clips let the panel float as it expands and contracts through Connecticut's temperature swings. No exposed fastener means no backed-out screws and no leak points along the panel field.
Nibbler and Hand Snips
We cut panels with a nibbler instead of a shear or grinder. Shear cuts leave a raw, rust-prone edge that fails in a few winters. Nibbler cuts keep the factory finish intact along every cut line.
Ice and Water Shield
Self-adhering membrane at the eaves, valleys and penetrations. It's the last line of defense when an ice dam pushes water uphill, and it's the layer most cheap bids leave out.
Fall Protection Harness
Every installer is tied off on OSHA-compliant fall protection, no exceptions. Steep 12/12 pitches and two-story drops are routine for us, and the harness is why nobody gets hurt on your property.
Magnetic Sweeper
We run it across the lawn, driveway and flower beds at least twice a day and once more at final cleanup. Roofing nails and metal shavings are the number one complaint about roofers, and we don't leave any.
Chalk Line and Tape Measure
Panel courses get laid out with a chalk line so the ribs run true from eave to ridge. A crooked first course shows up at the ridge, and we'd rather spend the extra 20 minutes than hand you a wavy roof.
Manufacturer Spec Installation
We install to GAF, Owens Corning and CertainTeed written specs, including fastener spacing, clip placement and underlayment overlap. That's what keeps your 40-year finish warranty valid. Deviate from spec and the manufacturer can deny a claim, so we don't.
Hose Testing
Before we call a job complete, we run water over valleys, chimney flashing and every pipe boot for 10 to 15 minutes. If a drop shows up inside, we fix it then, not after your first rainstorm. It's the cheapest insurance on the whole project.
Ventilation Balancing
We calculate intake at the soffits against exhaust at the ridge so the attic actually moves air. Undersized intake is the most common defect we find on Connecticut homes, and it's the root cause of attic condensation and decking rot.
Deck-Level Inspection
Once the old roof is off, we walk the decking and probe for soft spots with a pry bar. Rotted sheathing gets replaced before anything goes back down. Skipping this step is how a new roof leaks in year two.
01
What we do: We tear off to the deck, replace four sheets of rotted sheathing, and install 24-gauge standing seam in a dark bronze finish. Ridge venting gets corrected at the same time, and the chimney gets new counterflashing.
→ A roof that should outlast the owners' time in the house, with no more spring ceiling stains and a documented warranty they can hand a buyer.
02
What we do: Aluminum standing seam panels with a marine-grade finish go down over new ice and water shield, with stainless fasteners throughout. We spec the panel for the salt exposure, not a standard inland system.
→ No rust bleed at the fasteners, no chalky finish after two summers, and a roof that handles 70 mph coastal gusts without lifting.
03
What we do: We install a 24-gauge standing seam system with snow guards above the walkway and driveway, plus a reinforced eave detail. The steep pitch sheds snow fast, so the guards matter more than the panel.
→ Snow releases in controlled slides instead of one dangerous dump, and the roof carries the winter without a single ice dam call.
04
What we do: We price both snap-lock metal and a mid-grade asphalt system on the same sheet. The owner picks metal, we install it in four days between tenants, and we register the warranty to the property.
→ Repair calls drop to zero, and the owner writes off the annual shingle patch budget entirely.
Connecticut roofing is a snow-load and ice-dam problem first, a wind problem second, and a salt problem if you're near the Sound. Ground snow loads run 30 psf across most of the state and higher in the northwest hills, so we spec panels and fasteners for that load, not a national average. Building stock splits three ways: 1800s farmhouses with skip sheathing and no ridge venting, mid-century ranches with 4/12 pitches, and newer construction with engineered trusses. Each one gets a different panel profile and ventilation plan. Code-wise, we follow the Connecticut State Building Code and local permitting rules, and we pull the permit before a single panel comes off the truck. Coastal jobs in Pawcatuck, Stonington and Old Saybrook get aluminum or stainless fasteners to survive salt air. Inland jobs in Torrington, Goshen and Canaan get heavier snow guards and reinforced eave detailing. We're a Connecticut metal roof company that works in every one of those zones, and we'll tell you straight which system fits your house.
Litchfield Hills
Elevations above 1,000 feet carry heavier snow loads and longer winters. We spec 24-gauge panels and add snow guards over every walkway and driveway in this zone.
Shoreline Communities
Salt spray and wind-driven rain off Long Island Sound punish standard fasteners. Aluminum panels with stainless hardware are the default here, not an upgrade.
Farmington Valley
A mix of historic homes and newer subdivisions, with many roofs carrying undersized soffit intake. We correct ventilation during the metal install rather than after.
Naugatuck Valley
Steep pitches and mature tree cover mean more debris in valleys and more moss growth on north-facing planes. Panel smoothness ends the moss problem entirely.
Freeze-thaw cycles 60 to 80 times each winter
Water works into every seam and flashing joint, then expands. Metal panels move with the temperature instead of cracking, which is why they outlast asphalt here by decades.
Nor'easters driving rain sideways at 50 to 70 mph
Wind-driven rain finds gaps that a straight-down shower never would. We detail gable ends and ridges with extra closure strips and mechanical fastening.
Heavy wet snow followed by rain
That combination is what builds ice dams. A smooth panel sheds the snow before the rain arrives, and ice and water shield catches whatever backs up.
Summer attic temps pushing 130 degrees
Hot attics cook shingle underside and drive attic condensation. A vented metal system with balanced intake and ridge exhaust drops that temperature 15 to 25 degrees.
Most calls start with water where it shouldn't be. Here are the four failures we see most across Connecticut, and how a metal system ends the cycle instead of patching it.
Problem
Water stains, soggy insulation, peeling paint and eventually rotted framing at the eave. Each freeze-thaw cycle widens the gap under the shingles and makes the next leak worse.
Our Fix
We install ice and water shield along the full eave plus a smooth metal panel that sheds snow instead of holding it. Heat cable and snow guards handle the transition zones. Homeowners in Goshen and Morris stop buying ceiling paint every spring.
Problem
Exposed underlayment dries out, cracks and lets the next rain straight into the attic. Insurance deductibles add up fast when you're filing a claim every other year.
Our Fix
Standing seam panels are tested to 110 mph and higher, and there are no shingle tabs for wind to lift. We mechanically fasten through concealed clips, so a 60 mph gust doesn't find a weak point. One install ends the annual repair cycle.
Problem
Bare spots turn into leaks within a season or two, and the roof never passes another insurance inspection. Resale gets complicated when the buyer's inspector flags it.
Our Fix
Class 4 impact-rated metal panels absorb hail without cracking or losing surface. We document the upgrade for your insurer, and many carriers discount premiums for impact-rated roofing. The panel outlasts the mortgage.
Problem
Slow drips rot the sheathing around the penetration for years before you see a stain. By the time the ceiling shows it, the repair is three times the size of the original problem.
Our Fix
We rebuild chimney counterflashing, replace cracked pipe boots and reflash skylights with proper step and pan flashing during the metal install. Hose testing confirms every penetration before we call the job done.
Metal roofing services Connecticut homeowners pick for the long haul solve three problems asphalt never will: snow load, ice dams and wind uplift. Here's what you actually get.
Snow Slides Off Clean
A smooth standing seam panel sheds snow at roughly 30 psf, so a 12-inch snowpack releases instead of sitting on your rafters. That kills the ice dam cycle at the eave, where water backs up under shingles and stains your ceiling. We add snow guards above doorways and driveways so it releases in controlled slides, not one 200-pound dump.
40 to 70 Year Lifespan
How long does a metal roof last in Connecticut? Painted steel panels carry 40-year finish warranties and structural warranties up to 50 years; aluminum and copper run longer. Compare that to 15 to 20 years for asphalt shingles in our freeze-thaw climate, and the per-year cost flips in metal's favor by year 12.
Wind and Hail Rated
Class 4 impact panels shrug off the 1.5-inch hail that dents gutters and cracks shingle mats across Fairfield County. Standing seam systems are tested to 110 mph and higher, which matters when a nor'easter drives rain sideways into a gable end. No missing shingles, no exposed underlayment, no tarp calls at 2 a.m.
Lower Cooling Bills
A reflective painted panel or a cool-roof finish bounces summer sun instead of soaking it, and a vented airspace under the panel moves heat out of the attic. Homeowners in Simsbury and Ridgefield report attic temps dropping 15 to 25 degrees, which takes load off the AC and cuts attic condensation that rots roof decking from underneath.
Typical 2026 pricing for a full tear-off and metal install runs $14,000 to $38,000, or roughly $9 to $16 per square foot installed. That spread is real, not a sales tactic: panel gauge, roof complexity, decking condition and pitch all move the number. A simple gable ranch with snap-lock panels lands near the bottom. A steep, cut-up colonial with dormers, valleys and 24-gauge standing seam lands near the top. We price the whole job in writing before you commit, and we'll show you where you can save without cutting the layers that keep water out.
Typical Investment Range
$14,000 - $38,000 depending on roof size, panel type and complexity
A metal roof costs two to three times an asphalt replacement up front and lasts two to three times as long, with no annual patch bills in between. Spread over 40-plus years, the per-year cost is lower than shingles. You also get a documented warranty that transfers if you sell.
What changes the price
Panel Type and Gauge
26-gauge snap-lock panels cost less per square than 24-gauge standing seam, and stamped metal shingles sit between them. Gauge affects wind rating and dent resistance, so it's the first decision that moves the price.
Roof Size and Pitch
Square footage is the obvious driver, but pitch matters just as much. A 12/12 roof needs staging, more fall protection time and slower panel handling than a 5/12. Steep roofs can add 15 to 25 percent to labor.
Decking Condition
Once the old roof is off, we probe the sheathing. Rotted or delaminated decking gets replaced at a per-sheet price, and it's the one line item we can't quote until we see underneath. We photograph anything we replace.
Complexity and Penetrations
Dormers, valleys, chimneys, skylights and multiple roof planes all add flashing labor and material. A simple gable is fast. A cut-up roofline with six penetrations is not, and the quote reflects that honestly.
Trim and Add-Ons
Snow guards, upgraded ridge venting, gutter replacement and skylight flashing are priced separately so you can choose. We list them as options rather than burying them in a lump sum you can't audit.
Google ★★★★★4.9
Quoted standing seam and snap-lock on the same sheet with no pressure. Crew showed up when they said, swept the yard every day, and the ridge line is perfectly straight. Three days start to finish in Ridgefield.
BBB ★★★★★4.8
We had a leak over the kitchen and expected the worst. They traced it to chimney flashing, fixed that, and told us the metal roof was fine. Honest diagnosis and a fair invoice. That's why we'll call them for the next house.
Yelp ★★★★★4.9
Hail totaled our shingles and the insurance check was thin. These guys walked us through the math on a 40-year metal panel and it made sense. Clean install, warranty registered in our name, and the attic runs cooler.
We install metal roofing services Connecticut homeowners rely on across the whole state, from the northwest hills down to the shoreline. Each town has its own snow load, building stock and permit office, and we work in all of them. Here are some of the communities where our crews are on roofs every week.
Hilltop homes around Bethlehem carry heavier snow loads, so we spec 24-gauge panels and add snow guards above walkways and driveways.
Northwest corner properties in Canaan see long winters and deep frost. We detail eaves with full ice and water shield and reinforced fastening.
Danbury's mix of older colonials and newer subdivisions gets panel profiles matched to each roofline, with ventilation corrected during the install.
Large-lot homes in Easton often have complex rooflines with dormers and valleys. We price the flashing labor honestly instead of hiding it.
At higher elevation, Goshen roofs shed serious snow. Standing seam plus snow guards keeps the release controlled and the walkway clear.
Hawleyville sits near the I-84 corridor with a mix of commercial and residential roofs. We handle both pitched metal and flat TPO transitions.
Tree cover around Mansfield Center means debris in valleys and moss on north planes. A smooth metal panel ends the moss problem for good.
Rural Morris properties often include barns and outbuildings. We install metal on houses and agricultural structures with the same spec.
Lake-area homes in New Preston Marble Dale get wind-driven rain off the water, so we detail gable ends and ridges with extra closure strips.
Mid-century ranches in Northford usually need soffit intake corrected before metal goes on. We balance ventilation as part of the job.
Salt air near Pawcatuck demands aluminum panels and stainless fasteners. Standard steel will rust at the cut edges within a few winters.
Ridgefield's wooded lots drop limbs and debris on roofs every storm. Metal panels handle the impact that cracks asphalt shingles.
Simsbury's historic center and newer neighborhoods both get panel colors matched to existing trim, with samples shown before you commit.
Stevenson homes near the Housatonic valley see freeze-thaw cycles that destroy shingle edges. Metal moves with the temperature instead.
Torrington's steep pitches and older housing stock get a deck-level inspection before panels go down, with rotted sheathing replaced on the spot.
Real answers to the questions we hear most often from local homeowners and property managers.
New-construction and full-tear-off roof installation across Connecticut. We frame, deck and flash to spec, then set your metal panels or shingles on top. One crew, one warranty, no finger-pointing between trades if something leaks.
View Roof InstallationWhen repair math stops working, roof replacement gets you a clean deck and a fresh system. We strip the old layers, replace rotted sheathing and install ice and water shield before the new roof goes on. Most homes are done in 2 to 4 days.
View Roof ReplacementMetal roof repair Connecticut homeowners call for covers flashing failure, backed-out fasteners, punctured panels and storm damage. We match your existing panel profile and color where possible, and seal penetrations properly instead of smearing roof cement over the problem.
View Roof RepairRoof leaks rarely start where the stain shows. We trace water back to the actual entry point, whether that's a valley, a pipe boot or a chimney counterflashing, then fix it permanently. Hose testing confirms the repair before we pack up.
View Roof Leak RepairA 45-minute roof inspection catches curling shingles, flashing failure and early decking rot before they turn into a ceiling repair. You get photos, a written report and a straight recommendation on repair versus replace. No charge for the first look.
View Roof InspectionStorm damage, fallen limbs and active leaks get 24/7 response. We tarp and stabilize the roof the same day, document the damage for your insurance claim, and schedule permanent repairs once the weather clears. Call (844) 720-2263 any hour.
View Emergency Roofing ServicesCall (844) 720-2263 any time, day or night. For routine estimates we answer between 7 a.m. and 7 p.m., and emergency calls roll straight to a live dispatcher. You can also send photos of your roof through the website and we will reply with a ballpark range before we come out.
Phone
(844) 720-2263Address
Connecticut
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
