Full Tear-Off and Disposal
We strip every layer of old shingles down to the deck, pull the nails, and haul it all away in our own dumpster. No old roofing left in your yard, no hidden second layer that voids the manufacturer warranty.
Every full installation includes the complete roof assembly, not just shingles. Repairs are scoped separately and priced before we start. Here is what you get on a standard tear-off and re-roof.
We strip every layer of old shingles down to the deck, pull the nails, and haul it all away in our own dumpster. No old roofing left in your yard, no hidden second layer that voids the manufacturer warranty.
A self-adhering membrane rolled along the eaves, valleys and all penetrations. In Connecticut we run it at least 6 feet up from the eave line, which is what stops ice dams from backing water under your shingles in February.
A full synthetic underlayment layer over the deck plus new aluminum drip edge at every eave and rake. This is the secondary water barrier that catches anything the shingles shed sideways during wind-driven rain.
Step flashing at walls, chimney flashing, and new rubber pipe boots at every vent. Flashing failure is the number one cause of leaks we see, so we replace it rather than reusing old metal that has already started to fail.
We cut in ridge vents and confirm soffit intake is open so the attic breathes. Good ventilation is what keeps shingles from cooking from underneath and prevents attic condensation that rots decking from the inside.
We register your GAF or Owens Corning manufacturer warranty in your name and hand you the paperwork. As certified installers we can offer enhanced coverage that a non-certified roofer cannot register at all.
Asphalt Shingle Roofing in Connecticut is a layered roof assembly that sheds water, ice and UV through overlapping fiberglass-mat shingles nailed to a prepared deck. The job is never just shingles. We strip to the roof decking, inspect for rot, roll out ice and water shield along the eaves and valleys, lay synthetic underlayment, set new drip edge and flashing, then nail courses with a roofing nail gun using the manufacturer's pattern. Ridge vents and proper intake at the soffits keep the attic breathing so heat and moisture do not cook the shingles from underneath.
Connecticut roofs take a beating that flat, dry states never see: freeze-thaw cycles that pry up flashing, nor'easters that tear off ridge caps, and summer humidity that feeds moss growth on north-facing slopes. That is why local homeowners call us for asphalt shingle roof repair Connecticut after a storm, or for a full tear-off when shingles start curling at the edges. If you are pricing asphalt shingle roofing cost in Connecticut, the honest answer starts with what is under the shingles, not what is on top.
Every job follows the same five stages, whether it is a 12-square ranch in Bethel or a 40-square colonial in Glastonbury. You know what happens each day before the crew shows up.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Roofing nail gun and air compressor
Drives nails at the correct depth and pattern so shingle mats are not over-driven. Over-driven nails tear through shingles and are a leading cause of blow-offs in high wind.
Roofing shovel and pry bar
Strips old shingle layers without gouging the deck. We hand-pry around flashing and valleys so reusable structure is not damaged during tear-off.
Chalk line and tape measure
Sets straight, even course lines across the roof. Straight courses are what make a roof look right and keep shingle exposure consistent for proper water shedding.
Fall protection harness and ladder
Keeps every installer tied off on steep pitches. We run OSHA-compliant fall protection on every job, which protects our crew and your liability as the homeowner.
Magnetic sweeper
Pulls stray roofing nails out of the lawn and driveway after tear-off. We sweep twice, once at the end of each day and once at final walk-through.
Caulking gun and roof cement
Seals flashing, valleys and penetrations that shingles alone cannot protect. Used correctly it is a permanent detail, not a patch over a problem.
GAF Master Elite installation standards
We follow the manufacturer's nailing pattern, exposure and flashing details exactly, which is what allows us to register the enhanced GAF warranty. Deviating from those details is the fastest way to void coverage and shorten roof life.
Ice and water shield at eaves and valleys
A self-adhering membrane applied at least 6 feet up the eave line and through every valley. In a freeze-thaw state this is the single most important layer under the shingles, and we never skip it to save cost.
Balanced attic ventilation
We pair ridge vents with open soffit intake so air moves continuously under the deck. Balanced ventilation cuts attic heat in summer and condensation in winter, both of which age shingles from below.
Deck inspection and sheathing replacement
Every tear-off exposes the deck, and we inspect it board by board for rot, delamination and soft spots. Rotted sheathing gets replaced before anything goes back on, priced per sheet and approved by you first.
01
What we do: We do a full inspection with dated photos of the shingle field, flashing and decking, then write a remaining-life estimate the carrier accepts. If repairs will buy you years, we quote those first.
→ You get documentation for the insurer and a clear decision: repair now or plan a replacement. No guesswork, no pressure.
02
What we do: We tarp the opening the same day, remove the limb, and assess the deck and rafters. Once the weather clears we rebuild the damaged section and match the existing shingles.
→ Water stops entering within hours, and the permanent repair blends into the roof so you cannot spot the patch.
03
What we do: We re-nail and seal the ridge with upgraded caps rated for high wind, check the drip edge for corrosion, and replace any fasteners that have rusted through.
→ The ridge stops peeling off each storm, and the roof holds through the next nor'easter without another call.
04
What we do: We tear off both layers, inspect the decking, replace rotted sheathing, and install a full new assembly with ice and water shield and ridge vents.
→ A flat, solid roof with a registered manufacturer warranty, done in 2 to 3 days with the yard cleaned each night.
Connecticut sits in a freeze-thaw belt that most national roofing guides ignore. Roofs here see 40-plus freeze-thaw cycles a winter, which works nails loose, opens flashing seams and drives ice under the eave. Summer adds humidity that grows moss on shaded north slopes and bakes attics past 130 degrees. Building stock varies just as much: shoreline homes in Stamford and East Haven deal with salt air and wind-driven rain, while hill towns like Harwinton and Sherman fight snow load and ice dams. We detail each roof for its actual exposure. If you are comparing asphalt shingle roofing companies in Connecticut, ask what they run at the eave line. The answer tells you whether the roof will last 25 years or 12.
Shippan Point, Stamford
Coastal exposure means wind-driven rain and salt corrosion on fasteners. We spec corrosion-resistant nails and heavier ridge attachment on these roofs.
Glastonbury Center
Large older colonials with complex rooflines and multiple valleys. Valley flashing detail is where these roofs leak first, so we hand-seal every one.
Coventry Lake area
Tree cover and shade feed moss growth on north slopes. We treat moss and check attic ventilation on nearly every roof here.
New Milford river corridor
Older homes with steep pitches and original plank decking. We inspect decking closely because plank decks need different fastening than plywood.
Freeze-thaw cycling from December through March
Loosens nails, opens flashing seams and pushes ice under eave shingles. We counter it with ice and water shield and sealed flashing details on every job.
Summer attic heat above 130 degrees
Cooks shingle mats from underneath and shortens roof life by years. Balanced ridge and soffit ventilation is the fix, and we check it on every inspection.
Nor'easters and high-wind storms
Tear off ridge caps and edge shingles first. We upgrade ridge attachment and check the perimeter courses after every storm season.
Humidity and shade-driven moss growth
Lifts shingle edges and traps moisture against the mat. We treat moss, replace affected courses, and improve ventilation to stop it returning.
Most Connecticut roof calls come down to five problems. Here is what each one does if you leave it, and how we handle it.
Problem
Meltwater refreezes at the eave, backs up under courses, and soaks insulation and ceilings. Left alone it rots decking and stains every wall below.
Our Fix
We add ice and water shield up the eave line, fix the attic ventilation that caused the freeze in the first place, and repair any water-damaged decking. Most ice dam fixes run $800 to $2,500 depending on how much decking needs replacing.
Problem
Every missing shingle exposes underlayment and decking to rain. A single storm can turn a $600 repair into a $14,000 replacement within one wet season.
Our Fix
We tarp the same day if rain is coming, then match and install new shingles, reseal the surrounding courses, and check the ridge caps that usually fail first in high wind. Repairs typically take 2 to 4 hours.
Problem
Failed step flashing and chimney flashing leak slowly for years before showing up as a ceiling stain. By then the framing behind the wall is often wet and soft.
Our Fix
We open the detail, replace the flashing with new metal, and seal it with roof cement and proper counter-flashing. This is the repair we do most often, and it is usually a few hundred dollars instead of a full roof.
Problem
Connecticut humidity feeds moss that lifts shingle edges and holds moisture against the mat. Curling shingles then crack and blow off in the next storm.
Our Fix
We treat the moss, replace the worst-affected courses, and check attic ventilation, since shade plus poor venting is what grows moss in the first place. If the slope is past saving, we quote a partial or full replacement.
Asphalt shingles remain the most-installed roof in Connecticut for good reasons: they handle freeze-thaw, they are repairable, and they cost a fraction of slate or standing-seam metal.
Built for Freeze-Thaw
Connecticut swings from 10 degrees to 45 degrees in a single winter week, and that cycle is what kills cheap roofs. We install ice and water shield a minimum of 6 feet up the eave line and seal every valley, so meltwater refreezing at the gutter edge has nowhere to back up. A properly detailed shingle roof here lasts 20 to 30 years instead of 12.
Repairable, Not Disposable
When a limb punches through or wind peels a slope, we can match and weave in new courses instead of tearing off the whole roof. Most single-slope repairs take 2 to 4 hours and run $350 to $900. That repairability is why asphalt shingle roofing services Connecticut homeowners use tend to be shingle-first.
Warranty-Backed Materials
We install GAF Timberline, Owens Corning Duration and CertainTeed systems, and register the manufacturer warranty in your name. As a GAF Master Elite and Owens Corning Preferred Contractor, we can offer enhanced coverage that a non-certified installer cannot. That paperwork matters when you sell the house.
Fast Storm Turnaround
After a nor'easter we run 24/7 emergency tarping so a missing-shingle leak does not soak your ceilings overnight. Tarp-overs happen same day in most cases, and permanent asphalt shingle roof repair Connecticut work gets scheduled as soon as the weather breaks and the adjuster signs off.
Asphalt shingle roofing cost in Connecticut depends on size, pitch, layers to strip and decking condition, not on a flat per-square number. Typical 2026 pricing runs $9,000 to $18,000 for a full tear-off on an average home, or $450 to $750 per square installed. Repairs run $350 to $900. We measure, inspect the deck and give you a written, line-itemed price the same day, so you know exactly what you are paying for before we start.
Typical Investment Range
$350 - $18,000 depending on repair vs. full replacement and roof size
The cheapest bid usually skips ice and water shield, reuses old flashing or nails over the existing layer. Those shortcuts cost you a second roof years early. Our price covers the full assembly and a registered manufacturer warranty.
What changes the price
Roof size and pitch
Price is driven by squares, and a steep 10/12 pitch takes longer and more safety rigging than a walkable 5/12. A 1,500 square foot ranch and a 3,000 square foot colonial are very different jobs even with the same shingle.
Number of layers to strip
One layer tears off fast. Two or three layers add disposal weight, labor and dumpster cost, and they often hide deck damage. We always price tear-off to the deck so the new roof is not installed over a problem.
Decking condition
Rotted or delaminated sheathing gets replaced at a per-sheet price you approve first. A typical job replaces 0 to 6 sheets. Skipping this step is how cheap bids stay cheap and then leak within two years.
Shingle grade and brand
3-tab is the cheapest and shortest-lived. Architectural shingles like GAF Timberline or Owens Corning Duration cost about 30% more and last 10 to 15 years longer. Class 4 impact-rated shingles add more upfront but can lower insurance premiums.
Flashing, vents and penetrations
Chimneys, skylights, dormers and pipe boots all add detail work and materials. Replacing flashing rather than reusing old metal adds cost but is the difference between a dry roof and a recurring leak.
Access and disposal
Tight driveways, steep drops and landscaping that needs protection slow the crew down. We factor real access into the quote instead of surprising you with it later.
Google ★★★★★4.9
Tore off two layers and installed new architectural shingles in two days. They replaced rotted decking and showed me photos before covering it. Price matched the written estimate exactly, and they registered the warranty for me.
BBB ★★★★★4.8
Called after a storm tore shingles off our ridge. They tarped it the same evening and came back that week to repair. Matched the old shingles so well I cannot find the patch. Cleaned every nail out of the yard.
Yelp ★★★★★4.9
We had ice dam leaks two winters in a row. They found the real cause, bad attic venting, and fixed it along with the eave. Under $1,500 and no leaks since. Honest diagnosis instead of a hard sell on a new roof.
Google ★★★★★5.0
Full replacement on our colonial, done in three days with the yard cleaned every night. They walked me through the deck inspection and the flashing details. The crew was professional and the office answered every call.
We deliver asphalt shingle roof installation Connecticut homeowners can schedule statewide, from the shoreline to the northwest hills. Crews are routed by region, so a repair in Bethel and a replacement in Glastonbury both get handled without a long wait. Here are some of the Connecticut communities we serve most often.
Shingle roof repairs and full replacements for Bethel's mix of ranches and colonials, with ice and water shield detailed for the freeze-thaw cycles this area gets every winter.
Rural Brooklyn roofs deal with tree cover, moss and wind exposure. We handle moss treatment, shingle repair and full tear-offs with proper attic ventilation.
Coventry's shaded, wooded lots grow moss fast. We treat it, replace lifted courses, and check ventilation so shingles stop curling on north-facing slopes.
Shoreline East Haven homes face salt air and wind-driven rain. We spec corrosion-resistant fasteners and heavier ridge attachment on these roofs.
Glastonbury's large older colonials have complex valleys and chimneys. We hand-seal every valley and replace flashing rather than reusing old metal.
Hill-town snow load and ice dams hit Harwinton hard. We run ice and water shield well up the eave line and fix attic venting to stop the freeze.
Manchester's older housing stock often has two shingle layers. We tear off to the deck, replace rotted sheathing, and install a full new assembly.
Moosup roofs take wind and storm damage from nor'easters. We tarp same day and rebuild damaged slopes with matched shingles once weather clears.
New Milford's steep-pitch homes and plank decking need careful fastening. We inspect decking board by board and detail flashing by hand.
Northfield's wooded properties see moss and debris buildup. We clear valleys, treat moss, and repair or replace shingles as needed.
Oxford's newer construction and additions get full roof installation, decked and shingled to GAF spec with registered manufacturer warranty.
Redding Ridge homes sit under heavy tree canopy. We handle storm damage repair, moss treatment and full replacements with proper ventilation.
Sherman's hilltop exposure means high wind and ice. We upgrade ridge attachment and run ice and water shield up the full eave line.
Stamford's coastal and inland roofs both need wind-rated shingles and corrosion-resistant fasteners. We handle repairs, replacements and storm claims.
Thomaston's older homes often need decking repair along with new shingles. We replace rotted sheathing and install a complete new roof assembly.
Real answers to the questions we hear most often from local homeowners and property managers.
New-build and addition roof installation across Connecticut, decked and shingled to the same spec we use on replacements. If you are framing a garage or an addition, we handle the whole roof assembly from ice and water shield to ridge vent.
View Roof InstallationFull tear-off and replacement when your shingles are past saving. We strip to the deck, replace rotted sheathing, and install a complete GAF or Owens Corning system with a registered manufacturer warranty. Most Connecticut homes are done in 2 to 3 days.
View Roof ReplacementTargeted fixes for missing shingles, failed flashing, cracked pipe boots and small leaks. Repairs usually run $350 to $900 and take a few hours. We match your existing shingle and seal everything with new flashing and roof cement so the fix lasts.
View Roof RepairWe trace leaks to the actual source, not just the ceiling stain. Nine times out of ten it is flashing, a valley, or a nail pop, not the shingle field. We open it up, fix the detail, and water-test before we close it back in.
View Roof Leak RepairA full attic-to-ridge inspection with photos, covering decking, underlayment, flashing, vents and shingle condition. Ideal before buying a Connecticut home or filing an insurance claim. You get a written report and an honest remaining-life estimate, no charge.
View Roof Inspection24/7 tarping and emergency stabilization after storms, fallen limbs or sudden leaks. We secure the roof the same day so water stops entering, then schedule the permanent repair once the weather clears. Call (844) 720-2263 any hour.
View Emergency Roofing ServicesCall (844) 720-2263 any time, day or night. For routine estimates we answer between 7 a.m. and 7 p.m., and emergency calls roll straight to a live dispatcher. You can also send photos of your roof through the website and we will reply with a ballpark range before we come out.
Phone
(844) 720-2263Address
Connecticut
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available